- Home
- ยป
- Our Product Range
- »
- Commercial Ro System
Commercial Ro System
Spectrum Aqua Private Limited is a leading Industrial RO Plant Manufacturer in India that not only manufacture water treatment products but also wastewater treatment products such as sewage treatment plant, effluent treatment plant and that too compact.
The company established as an integrated service provider of design, fabrication, installation, and maintenance services. We are one of the most trusted partners for waste management solutions. Spectrum’s waste management experts will treat your system and proactively respond to your needs like they’re our own—allowing you to focus on what you do best every day.
Our market focus and experience include effluent treatment, sewage treatment, commercial reverse osmosis, industrial and municipal wastewater treatment, and reuse.How does an Industrial RO Plant Work?
The raw water is pumped through the disc filter where large colloids and particles are removed and further reaches the multigrade filter which removes turbidity, sediments, dirt from the water and acts as a protection to the RO membrane. Further, the water reaches the activated carbon filter which removes odor, color, small particles like chlorine organics, etc.
The raw water then enters the Antiscalant Dosing System which pumps chemicals in the water to prevent scale formation on the edges of the RO Membrane followed by micron filter which further removes turbidity up to 5 microns. The in-process water enters into the pressure pump which increases the flow and pressure of water and enters into a Reverse Osmosis Membrane which helps in removing dissolved colloids, bacteria, viruses and all particles with pores size as low as 0.0001 microns.
The water then enters Rotameter (it check the flow of final water, rejected water & recirculated water). The ultraviolet system embedded in the RO Water Plant System removes residual bacteria, viruses further acting as a disinfectant. Finally, we get fresh and pure water to die down our thirst.
The process is repeated again by entering into the CIP cleaning system that takes a course of action by removing the scales from the RO membrane and the cycle to obtain pure water is repeated again.
The Technology Used in The Reverse Osmosis Plant
1. RO Purification
2. UF Purification
3. UV Purification
4. Candle Filter Purifier
5. Activated Carbon Filter Purifier
Puredrop Stainless Steel Commercial RO System 25 LPH PD-28 Model
Minimum Order Quantity: 1 Piece
Product Brochure
| Purification Capacity | 25 LPH |
| RO Capacity | 25 Liter |
| Automation Level | Fully Automatic |
| Material | Stainless Steel |
| Automation Grade | Automatic |
| Purification Type | Reverse Osmosis |
| Model Name/Number | PD-28 |
| Usage/Application | Water Purification |
| Brand/Make | Pure Drop |
| Number Of Membranes In Ro | 2 |
| Voltage | 120-250 V A C (50Hz) |
| Min Order Quantity | 1 |
| Brand | PURE DROP |
| Types Of Machines | Commercial RO System |
| Treatment Technique | Reverse Osmosis |
| Product Dimensions | 375 x 205 X 470 Cm |
| Warranty | 1 year |
| Installation Type | Complete Civil work with Installation |
| Water Purification Process | Reverse Osmosis |
| Certification | ISO9001:2008 |
| Country of Origin | Made in India |
| Net Weight | 20 Kg. Approx |
| Operating Voltage | 24 V DC To 48 DC |
| Input Voltage | 120-250 V A C (50Hz) |
| M in. Inlet Water Pressure | 0.3 kg/cm 2 |
We are one of the prominent firms involved in the provision of highly qualitative Upto 25 LPH RO System. These systems are developed using premium quality of raw materials as per industrial standards of quality. All our products are quality checked on the current industrial parameters by our trained personals.
Technical Specifications:
| Technical Specification | PD 30 |
| Model | 25 LPH |
| Purification Capacity | 25* Liters/H our |
| M ax. D duty Cycle 2 | 200 Liters / Day |
| Filter Cartages | Sediment, GA C, CTO |
| RO Membrane | 1812-75 G PD /CSM 100 /300G PD |
| RO Pump | K /F 4 8 V |
| M in. Inlet Water Pressure | 0.3 kg/cm 2 |
| Input Voltage | 120-250 V A C (50Hz) |
| Operating Voltage | 24 V DC TO 48 DC |
| Dimensions | L 375 W 205 H 470 |
| Net Weight | 20 Kg. Approx |
Additional Information:
- Item Code: PD-28
- Delivery Time: Within 24 Hours
Puredrop Commercial RO System 200 LPH
Minimum Order Quantity: 1 Piece
Product Brochure
| Purification Capacity | 200 LPH |
| RO Capacity | Up to 1000 ltr/hr |
| Automation Level | Fully Automatic |
| Working Pressure | More than 200 PSI |
| Material | Stainless Steel |
| Frame Material | Stainless Steel |
| Included Components | Water Softener |
| Automation Grade | Automatic |
| RO Membrane Type | Thin-Flim Composite (TFC) |
| Media | Activated Carbon + sand |
| Number Of Membranes | 1 |
| Water Source | Bore Water |
| Usage/Application | Industrial |
| Mounting Type | Floor Mounted |
| Plant Accessories | Ultra Filtration Plant |
| Warranty | 1 Year |
| Plant Application | Factory/Industry, Hospital, Residential, Restaurant/Hotel, School/College, Office |
| Number Of Membranes In Ro | 1 |
| No. of Membrane Housing | 1 |
| Installation Type | Complete Civil work with Installation |
| Deliver Type | Pan India |
| Installation Service | Yes |
| Power Source | Electric |
| I Deal In | New and Second Hand |
| Country of Origin | Made in India |
Puredrop 50 LPH Commercial Reverse Osmosis System PD-29
Minimum Order Quantity: 1 Piece
Product Brochure
| Capacity | 50 LPH |
| Capacity (Purification Rate) | 50 LPH |
| Plant Type | Commercial |
| Application / Type | Commercial |
| Purification Technology | RO |
| Material | Stainless Steel |
| Frame Material | Stainless Steel |
| Water Storage Capacity | 50 Liter |
| Type Of Purification Plants | Reverse Osmosis |
| Purification Type | Reverse Osmosis |
| Model Name/Number | PD-29 |
| Mounting Type | Floor Mounted |
| Usage/Application | Industrial |
| Number Of Membranes In Ro | 4 |
| Application | Commercial Use |
| Voltage | 100-300 V A C (50Hz) |
| Installation Services Required | Yes |
| Capacity Inlet Flow Rate | 50 L/Hour |
| Brand | Pure Drop |
| Installation Type | Complete Civil work with Installation |
| Weight | 30 Kg |
| Country of Origin | Made in India |
| Automation Grade | Automatic |
| Automation Level | Semi-Automatic |
PD-31
Technical Specification:-
• Model : Industrial 50 LPH
• Purification Capacity : 50 Liters/Hour
• Max. Duty Cycle : 6 hour
• Stand : Slandered steel Skid
• Housing : 3 Housing 20�?
• Pump : 2 Den Yang 250 GPD/Kemflow-48
• Filter Cartages : 20�? Sediment 5 Micron and CTO
• Membrane : 4 PIC DOW 75 GPD/CSM 100 GPD
• Input Voltage : 100-300 V AC (50 Hz)
• Operating Voltage : 48 V DC
• Inlet water pressure : 0.3 Kg/cm2 (Min.)
• Dimensions : L 25 W 38 H 102
• Net weight : 30 KG. Approx.
Note: - Purification capacity tested for raw water having TDS
value of 1000 PPM at room temperature and output 60 TDS
Approx. This value may increase decrease on the quality of
water and temperature
Additional Information:
- Item Code: PD-31
- Delivery Time: Within 24 Hours
- Packaging Details: L 25 W 38 H 102
100 Lph Ro System (covered)
| RO Capacity | 100 LPH |
| Working Pressure | 100 PSI |
| Automation Grade | Automatic |
| Material | Mild Steel |
| Country of Origin | Made in India |
Purification Capacity : 100 Liters/HourMax.
Duty Cycle : 4-6 hour
Stand : Slandered Mild Skid
Housing : 3 Housing 20”
Pump : 3 Puredrop 300 GPD
Filter Cartages : 20” Sediment 5 Micron and CTO
Membrane : 3 PIC 300 GPD
Input Voltage : 100-300 V AC (50 Hz)
Operating Voltage : 32 V DCInlet
Water Pressure : 0.3 Kg/cm2 (Min.)
Dimensions : L 25 W 38 H 102
Net weight : 30 KG. Approx.
Note:- Purification capacity tested for raw water having TDS value of 2000 PPM at room temperature and output 60 TDS Approx. This value may increase decrease on the quality of water and temperature
Puredrop 50lph Commercial Ro System
Minimum Order Quantity: 1 Piece
| Purification Capacity | 50 LPH |
| Automation Level | Fully Automatic |
| Frame Material | Mild Steel (MS) |
| Included Components | Carbon Filter, Pre-Filter |
| Number Of Membranes | 4 |
| Mounting Type | Floor Mounted |
| Warranty | 1 Year |
| Plant Application | School/College, Office, Residential, Restaurant/Hotel, Hospital, Factory/Industry |
| Category | Specifications |
|---|---|
| Capacity & Performance | - Purification Capacity: 50 LPH- Recovery Rate: 30–45%- Salt Rejection: 95–98%- Output Water TDS: < 50 ppm (depends on feed TDS) |
| Feed Water Requirements | - Maximum Feed TDS: 2000 ppm- Feed Pressure: 1–3 kg/cm²- Feed Temperature: 10–35°C- pH Range: 6.5–8.5- Turbidity: < 5 NTU- Recommended Hardness: < 500 ppm |
| Pre-Filtration | 1. 10 Micron Sediment Filter2. GAC Carbon Filter3. 5 Micron Sediment FilterOptional: Anti-scalant dosing, iron removal filter |
| RO Membrane System | - Membrane Size: 1812 / 2012- Membrane Type: TFC (Thin Film Composite)- Membrane Qty: 1 or 2 (model-dependent)- Operating Pressure: 8–14 kg/cm² |
| High-Pressure Pump | - Pump Type: Commercial RO Pump- Motor Power: 0.5 HP / 0.75 HP- Pump Material: SS / Food-grade polymer |
| Controls & Safety | - Low-Pressure Switch (Dry run protection)- High-Pressure Switch- Auto Flush System- Solenoid Valve- Float Switch / Auto Cut-Off- Optional: Digital TDS meter |
| Post-Filtration | - Inline Carbon Filter (taste improvement)- Optional: UV Sterilizer, Alkaline/Mineral Cartridge |
| Construction & Build | - Frame: MS powder-coated / Stainless Steel- Piping: Food-grade tubing- Fittings: Quick-connect- Storage Tank (Optional): 50–100 L (SS or food-grade plastic) |
| Power Requirements | - Voltage: 220–240V AC- Frequency: 50 Hz- Power Consumption: 200–350W |
| Dimensions & Weight | - Typical Dimensions: 500 × 350 × 850 mm (L×W×H)- Weight: 25–35 kg |
| Applications | Restaurants, cafés, offices, schools, clinics, labs, small industries, food units |
| Standard Accessories | Pressure gauge, FRP housing, tubing & fittings set, installation kit, user manual |
Additional Information:
- Delivery Time: Within 24 Hours
Puredrop 25 Lph Commercial Ro System
Minimum Order Quantity: 1 Piece
| Purification Capacity | 25 LPH |
| Automation Level | Fully Automatic |
| Frame Material | Mild Steel (MS) |
| Included Components | Pre-Filter |
| Number Of Membranes | 2 |
| Mounting Type | Wall Mounted |
| Warranty | 1 Year |
| Plant Application | Hospital, School/College, Office, Factory/Industry, Restaurant/Hotel, Residential |
| Category | Specifications |
|---|---|
| Capacity & Performance | - Purification Capacity: 25 LPH- Salt Rejection: 95–98%- Recovery Rate: 30–40%- Output Water TDS: < 50 ppm (based on feed TDS) |
| Feed Water Requirements | - Max Feed TDS: 1500 ppm (upgradeable)- Feed Pressure: 1–3 kg/cm²- Feed Temperature: 10–35°C- pH Range: 6.5–8.5- Turbidity: < 5 NTU |
| Pre-Filtration Stages | 1. 5 Micron Sediment Filter2. Granular Activated Carbon (GAC)3. 1 Micron Spun FilterOptional: Anti-scalant dosing system |
| RO Membrane System | - Membrane Type: TFC (Thin Film Composite)- Membrane Size: 1812 / 2012- Quantity: 1- Operating Pressure: 7–12 kg/cm² |
| High-Pressure Pump | - Type: Commercial RO Booster Pump- Motor Capacity: ~0.5 HP- Material: Stainless steel / food-grade polymer- Rated for continuous 25 LPH output |
| Automation & Safety Controls | - Low-Pressure Switch (dry run protection)- High-Pressure Switch (over-pressure safety)- Solenoid Valve for automatic feed control- Auto Flush System (manual/auto)- Float Switch / Auto Cut-Off |
| Post-Filtration | - Inline Carbon Filter (taste & odor improvement)Optional: UV Sterilizer, Mineral/Alkaline Cartridge |
| Construction & Build | - Frame: MS powder-coated / Stainless Steel- Piping: Food-grade tubing- Fittings: Quick-connect type- Optional Storage Tank: 25–50 liters (SS or food-grade plastic) |
| Electrical Requirements | - Voltage: 220–240V AC- Frequency: 50 Hz- Power Consumption: 150–250W |
| Dimensions & Weight | - Typical Size: 450 × 300 × 700 mm (L × W × H)- Weight: 20–25 kg |
| Suitable Applications | Offices • Clinics • Labs • Cafés • Retail shops • Schools • Small industries • Homes/commercial hybrids |
| Standard Accessories | Pressure gauge • FRP membrane housing • Tubing & fittings • Installation kit • User manual |
Additional Information:
- Delivery Time: Within 24 Hours
Puredrop Industrial UV System
Product Brochure
| Brand | Concept |
| Automation Grade | Automatic |
| Usage/Application | Industrial |
| Power Source | Electric |
| Country of Origin | Made in India |
Features:
• Minimum maintenance
• Long-lasting service
• Optimum performance
• Rust-resistant
• Philips UV lamp
Application:
Eliminates bacteria, viruses, molds and yeast
Puredrop Commercial Water Purifier PD-23
Minimum Order Quantity: 1 Piece
Product Brochure
| Capacity (LPH) | 500 LPH |
| RO Capacity | 500 (Liter/hour) |
| Purification Technology | RO + UV |
| Filter Type | Ultra Violet Filtration System |
| Type Of Machines | U Literati Filtration |
| Material | Stainless Steel |
| Filter Medium Material | Ultra Violet Filtration System |
| Automation Grade | Automatic |
| Flow Rate | 0-500 |
| Purification Type | Ultra Violet Filtration System |
| Model Name/Number | PD-23 |
| Brand | Pure Drop |
| Capacity | 500 Liter per hour |
| Model Type | PD-23 |
| Usage/Application | Water Purification |
| Country of Origin | Made in India |
Additional Information:
- Item Code: PD-26
- Delivery Time: Within 24 Hours
50 LPH Commercial Ro System (9500+gst/without warranty)
Minimum Order Quantity: 1 Piece
Product Brochure
| Purification Capacity | 50 LPH |
| Automation Level | Fully Automatic |
| Purification Type | RO + UV + UF |
| Material | FRP |
| Automation Grade | Automatic |
| Installation Type | Wall Mounted/ Counter Top |
| Plant Application | Factory/Industry, Hospital, Office, Restaurant/Hotel, School/College, Residential |
| Country of Origin | Made in India |
Product Specifications for 50 LPH Commercial RO System
- Capacity: 50 Liters per Hour (LPH)
- Power Supply: 220V AC, 50Hz (single-phase)
- Working Pressure: 4-6 Bar (58-87 psi)
- Recovery Rate: 45%-55% (depending on water quality)
- Operating Temperature Range: 5°C - 45°C
- Membrane Type: Thin Film Composite (TFC) Reverse Osmosis Membrane
- Feed Water Quality: Municipal water, Borewell water (depends on source quality)
- Dimensions: Varies based on design (typically 600mm x 400mm x 800mm)
- Weight: Approximately 25-35 kg (depends on specific model and components)
- Water Output Quality: TDS Reduction of up to 95%-99% (depends on feed water quality)
- Pre-Filter: Activated Carbon and Sediment Filter
- Control Panel: Automatic ON/OFF and low-pressure protection
- Reject Water: Approximately 1.5 to 2.5 litres of waste per litre of purified water (depends on the quality of feed water)
Components of the 50 LPH Commercial RO System
- Pre-Filtration Stage:
- Sediment Filter: Removes larger particles like dust, dirt, and rust from the feed water, protecting the RO membrane.
- Activated Carbon Filter: Absorbs chlorine, volatile organic compounds (VOCs), and bad odours, ensuring better water quality and protecting the RO membrane from chlorine damage.
- High-Pressure Pump:
- Boosts the water pressure to the required level for reverse osmosis to work effectively, ensuring high water recovery.
- Reverse Osmosis Membrane (TFC):
- The core filtration element that removes dissolved solids, salts, bacteria, and other contaminants from the water.
- Flow Restrictor:
- Regulates the flow of water and ensures proper filtration by maintaining the correct pressure within the membrane chamber.
- Post-RO Filter:
- Mineral Filter (optional): Adds essential minerals back to the purified water, improving taste and ensuring health benefits.
- UV Sterilizer (optional): Ensures additional disinfection of the water by destroying any remaining microorganisms.
- Storage Tank:
- Stores purified water for immediate use. Typically made from food-grade materials to ensure safe and clean water storage.
- Automatic Control Panel:
- Features include system status monitoring, automatic start/stop, low-pressure protection, and indicators for filter change and system maintenance.
- Reject Water Line:
- Directs the wastewater produced by the RO system (brine water) to the drain.
- Pressure Gauges:
- Monitors the pressure levels at different stages, ensuring optimal performance and alerting to potential issues like clogged filters or pump failure.
- Flow Meters:
- Measures the amount of filtered and wastewater produced, providing data for better system monitoring.
- Water Inlet and Outlet Ports:
- Easy-to-connect fittings for the feed water input and purified water output.
Additional Information:
- Item Code: PD-50
- Delivery Time: Within 24 Hours